How To Repair Bathtub Tules

Download Commodity

Download Article

Over fourth dimension, your bath tiles may get damaged or look outdated, simply fortunately, you lot tin can supervene upon them in an afternoon. Whether you're replacing tiles on the bath wall or floor, first cutting out and remove the quondam tiles to clean out the area. When you're ready to install your new tile, utilize a layer of mortar or thin-set to hold the tiles in place before applying grout between them. When you're finished, your bath will have a fresh, new look!

1. 1

   Remove whatsoever fixtures that surround your tiles to prevent damage. Bank check if any of the tiles you lot're replacing intersect with any of the fixtures in your shower, such equally the shower caput, faucet, or overflow drain. Unscrew or pull the fixtures off of the wall and set them bated for now so you can reinstall them after.^[ane]

   • You don't need to remove the fixtures if you're only replacing single tiles that aren't in the fashion of your fixtures.
   • If you don't experience comfy taking out the fixtures yourself, and so contact a plumber or a contractor to come do the work for you.

2. ii

   Encompass your workspace and drains with a drop cloth to prevent whatsoever damage. Falling tile pieces tin can scratch or harm your bath or flooring underneath them. Spread a drop cloth over the entire area where y'all're working and use painter'due south record to secure it in place then it doesn't slip or motility around. Make sure the tub drain is completely covered if y'all're removing shower tiles so none of the pieces get stuck in your pipes.^[two]

   • If you don't have a driblet cloth, you can employ one-time bedsheets instead.

   Advertising

3. 3

   Cutting through the grout effectually the tiles with a grout removal tool. ^[3] Grout removal tools have saw-similar teeth that hands grind through grout to make it easier to remove. Start the blade in one corner of the tile and pull it straight across the grout to cut into it. Get over the area a few times applying a medium corporeality of force per unit area to completely remove the grout. Cutting through each line of grout effectually the tile so you're able to pry information technology out of place.^[4]

   • Work through the grout around 1 tile at a time so it'southward easier to remove.
   • Y'all don't accept to remove the grout from the tiles at this signal if you don't want to, only it makes the tiles easier to remove and volition aid go along your workspace cleaner.

4. 4

   Pry the tiles off of the wall with a hammer and flat chisel. First at the outer edge of the acme row of tiles to make them the easiest to remove. Hold the cease of a apartment chisel against the edge of the tile at a 30-degree angle. Tap the other terminate of the chisel with a hammer to force the chisel under the tile and remove it from the wall. Work completely beyond each row from top to lesser.^[5]

   • Put on work gloves and condom glasses to protect yourself from any tile shards or sharp edges.
   • Wearable long pants while yous're working since the tiles could autumn and cut you.
   • The sometime tiles may suspension when y'all chisel them out of place or when they fall downwardly.

   Tip: If you're replacing a single wall tile in the middle of other tiles, drill a hole in the center of it and commencement your chisel in the eye. This way, y'all're less likely to harm any of the other tiles.^{[half dozen]}

5. v

   Scrape off any leftover agglutinative with a metal scraper. ^[seven] Afterward y'all remove all of the tiles, at that place may still be some sections of mortar withal stuck on your wall. Hold a metal scraper at a 45-degree bending to the agglutinative and employ a business firm amount of pressure to lift upward the adhesive. Go along scraping information technology to remove equally much as you can before moving on.^[eight]

   • If you lot take trouble removing the mortar with a metal scraper, use your flat chisel and a hammer to utilize more pressure level.

6. six

   Castor the drywall then y'all can get a clean application. Use a potent-bristled store brush to wipe whatever dust or debris from the area. Start at the pinnacle of your wall and castor in brusk strokes down to push whatsoever residual fabric onto your drop cloth. Proceed brushing the wall until you don't see it lift up whatsoever more than dust.^[9]

   • Y'all can too use the hose attachment on your vacuum to clean your walls, but brand sure you don't suck upwards large tile pieces since they could cut the hose or damage the inside of your vacuum.

7. 7

   Measure and plan the tile layout. Find the dimensions of the area where you plan on reinstalling new tiles and write them downwards and then yous don't forget. Then check the dimensions of the tiles y'all're using to run into how they will fit on your wall. Calculate the area of the wall and divide information technology by the expanse of a single tile and so y'all know how many tiles you need for your space. Choose to line up your new tiles in a grid blueprint or showtime them slightly to make the space more than visually interesting.^[10]

   • For example, if your bathroom wall is 30 foursquare feet (2.viii m²) and your tiles each cover ^ane⁄_two square foot (0.046 thousand²), then you lot'll need 60 tiles full.
   • You don't need to program a layout if you're merely replacing a single tile, but make sure the measurements are the same.
   • Y'all may need to cut the tiles to a specific size if they don't perfectly fit on your wall.

8. eight

   Spread a sparse layer of tile mortar onto your wall with a foursquare notch trowel. ^[11] Scoop out a large blob of the tile mortar from the container and spread it on your wall. Merely comprehend a department that'south almost 3–4 foursquare anxiety (0.28–0.37 yard²) so it doesn't dry earlier you're able to identify your tiles. Drag the edge of a square notch trowel over the mortar to get out grooves in it so the mortar has room to expand when y'all press a tile onto it.^[12]

   • You can either purchase premixed tile mortar or you can mix information technology yourself.

   Tip: If you're applying a single wall tile, then employ the mortar to the dorsum of the tile instead of directly on the wall and then the mortar doesn't set on the surface of some other nearby tile.

9. 9

   Push the tile onto the mortar so it holds in place. Concord the tile carefully past the edges and line it upward on your wall so it's even and level. Push the tile into the space where you desire to put information technology and press information technology firmly against the wall and so it sticks to the mortar. Apply force per unit area to the entire surface of the tile to get an even mortar application on the back.^[13]

   • If y'all desire to check if at that place'due south enough mortar, slowly peel the tile off the wall and bank check the dorsum to run across if it has even mortar coverage.

10. x

    Install the other tiles on your wall with spacers in between them. Work in horizontal rows from the bottom to the top and then the tiles look even and level. Go along applying more mortar as you need to install your new tiles and press them into place and then they stick to the wall. Slide 1-ii spacers on every side of the tiles so they stay a uniform altitude apart, or else they'll get crooked. Allow the mortar gear up for 24 hours and then it can dry out.^[14]

    • You can purchase tile spacers from your local hardware store.
    • Make sure that the tiles are pressed the same depth against the wall or else they'll exist uneven.

11. xi

    Use grout to your tiles after the mortar sets for 24 hours. ^[15] Pull the spacers out from your wall so you lot take a clean work surface. Follow the directions on the package of grout and mix it until it has a thick enough consistency where yous can form it into a ball. Pick upward some of the grout on the end of a rubber grout float, which is like a duster, and work it into the spaces between the tiles. Start at the edges of your tiles and pull the float beyond the edges diagonally to force the grout inside.^[16]

    • You can purchase grout and a grout float from your local hardware store.
    • Make sure to evenly employ your grout then information technology doesn't look thicker or thinner in any spots.

12. 12

    Wipe off any remainder grout with a clean sponge. After about 20 minutes, moisture a sponge under warm h2o and wring information technology out so it isn't dripping wet. Wipe the surface of the tiles to remove whatever grout that's stuck on them. Rinse the sponge when it looks dingy and go on cleaning off your tiles until there isn't any grout left on the surface.^[17]

    • Be careful not to remove any of the grout from between your tiles since it may still be slightly wet.

13. xiii

    Reinstall your fixtures in one case the grout sets. Wait at to the lowest degree i day for your grout to completely set between your tiles so it hardens completely. Reattach the fixtures past reversing the process you used to remove them. Make sure they're tightly secured to the wall so they don't cause whatever leaks or impairment to the tiles.

    • Y'all may need to caulk around some fixtures so water can't get within or underneath them.

    Advertisement

1. i

   Scrape the grout out from between the tiles. Employ a grout removal tool with a serrated border to cut through the grout betwixt your tiles. Outset near the corner of ane of your tiles and apply a firm amount of pressure level to dig into the grout. Pull the grout removal tool between the tiles 3-4 times to cut out as much as yous can from the wall. Continue scraping the grout between each of tiles you plan on replacing.^[18]

   • You can buy grout removal tools from your local hardware shop.
   • Remove all the grout and accept out 1 tile at a time to make your workload easier.

2. 2

   Pry the tiles upwardly from the floor with a hammer and chisel. Position the flat cease of your chisel on the edge of the tile yous're removing at a 30-degree angle. Lightly tap the end of the chisel with a hammer or rubber mallet to break the tile off of your floor. If you can't lift the tile later on hitting it from i side, try positioning your chisel on the opposite side and prying it from in that location. Continue removing the other tiles the same manner.^[19]

   • Begin on one of the tiles along the outer edge of your room if you plan on replacing the whole tile floor so you take an easier starting point.
   • If you work slowly and advisedly, you may exist able to remove your floor tiles without breaking them.

   Tip: Continue a box or a trash can nearby to throw abroad the tiles as you lot remove them and then your workspace doesn't get every bit muddied.

3. three

   Remove the residual agglutinative with a metallic scraper. Hold a metal scraper at a 45-degree bending to your floor at the border of the mortar that's withal stuck. Utilise a business firm amount pressure and push button the scraper forward to lift up the adhesive. Go on working across the surface of your flooring until you've lifted as much of the mortar as y'all can.^[xx]

   • Use your chisel and a hammer to pry stuck-on adhesive if you aren't able to lift it with a metallic scraper.

4. 4

   Vacuum your bath to remove whatsoever dust or droppings. Your tiles volition leave shards and dust in your bathroom, which may prevent your new tile from staying in place. Use the hose attachment on your vacuum to lift up modest bits of tile or agglutinative that you weren't able to clean upwardly easily. Continue working until yous've removed as much of the debris as you lot can.^[21]

   • Don't use your vacuum on shards that are larger than a coin since you lot could impairment the hoses or bag.

5. 5

   Measure and plan the layout for your floor tiles. Detect the dimensions of your bathroom and write them down and then you can run into how many tiles will fit. So accept measurements of the new tiles that you plan on installing so you can offset designing how you want to place them. Calculate the total surface area of your bathroom and divide information technology by the expanse of 1 tile so you know how many you need to become. Lay your tiles on the floor to program how you want them to expect when you're finished.^[22]

   • For example, if you have a bathroom that's 40 square anxiety (iii.7 m²) and each tile covers one foursquare foot (0.093 m²), and so you'll need xl tiles full.
   • You tin can choose to lay out your tiles in any pattern you want, but yous may need to cut some if they don't fit in the infinite.
   • Take multiple pictures of your layouts so you lot can compare them adjacent.
   • Y'all do not need to programme a layout if you're but replacing a single tile.

6. half dozen

   Use sparse-set onto a 3–4 sq ft (0.28–0.37 m²) department of your floor. Kickoff on the side of your bathroom furthest from the door. Buy premixed thin-set or follow the directions carefully on a powdered mix so you lot get the right consistency. Use a foursquare notch trowel to spread the sparse-gear up over an area that's 3–iv square anxiety (0.28–0.37 one thousand²) then information technology can't dry out before you lot place the tiles. Become over the sparse-set with the notched side of the trowel to brand grooves in it then the tile sticks amend.^[23]

   • If you're just replacing a unmarried tile, you can either spread the sparse-ready onto the dorsum of the tile or into the space where you're placing the tile.

7. vii

   Push the tile into place on the thin-set. Line up the tile with the area where you desire to place it and carefully set information technology down in place. Apply a house amount of pressure level so it firmly adheres to the sparse-set and make sure the tile stays straight then information technology doesn't announced crooked. If you need to apply more pressure to the tile, lightly tap it with a rubber mallet until it sets into identify.^[24]

   • Set a level on tiptop of the tile to make sure it'due south flat on superlative of the thin-set. If it'south not, utilise pressure to the raised sides.

8. 8

   Go along calculation tiles to your floor with spacers in between them. Work in horizontal rows across your bath flooring and so you tin can ensure your tiles stay straight. Spread more than thin-set on the floor when you need it and identify the next tiles side by side for the first one. Check that the tiles are level with one some other before sliding i-2 spacers between them so they stay the same distance apart. Identify the same number of spacers between all of your tiles so the flooring looks uniform and fifty-fifty.^[25]

   • You tin can buy spacers that also aid level your floors to make your workload easier.
   • Work from the furthest corner of your bath toward the door so you have an piece of cake mode to get out when y'all're finished laying the tiles.

9. 9

   Spread grout in the spaces between the tiles once the thin-set is dry. Leave the sparse-prepare to dry for at least 24 hours before pulling the spacers out from between your tiles. Mix your grout post-obit the package's instructions and scoop some out with a rubber grout bladder. Push the grout float diagonally into the spaces betwixt your tiles to force the grout betwixt them. Check that the meridian of the grout is even with the top of the tile and fills in the space completely. If the awarding looks uneven, then wipe out any backlog with a shop cloth.^[26]

   • You tin can buy grout from your local hardware or habitation improvement store.
   • Don't employ a regular trowel for spreading your grout since you may scratch or damage your new tiles.

10. 10

    Wipe away excess grout with a damp sponge. ^[27] About 20 minutes later you utilize the grout, wet a sponge nether warm water and wring it out so it's damp to the touch. Carefully make clean the tiles on your floor to remove any grout that's nevertheless on their surfaces. Be careful not to remove any of the grout between the tiles since it yet may be wet.^[28]

    Advertisement

Add together New Question

• Question

  How practice I start replacing tiles in my bathroom?

  

  Art Fricke
  Home Renovation & Repair Specialist

  Art Fricke is a home renovation and repair specialist and the owner of Art Tile & Renovation based in Austin, Texas. With over 10 years of feel, he specializes in bathroom and kitchen renovations. Art focuses on a single contractor approach to customized renovation work, and performs projects such as installing custom tile showers, fixing tiled shower leaks, replacing cracked tiles, and installing flooring and wall tile.

  

  Home Renovation & Repair Specialist

  Proficient Answer

• Question

  How do I remove bathroom tiles?

  

  Art Fricke
  Habitation Renovation & Repair Specialist

  Fine art Fricke is a dwelling renovation and repair specialist and the owner of Art Tile & Renovation based in Austin, Texas. With over 10 years of experience, he specializes in bath and kitchen renovations. Art focuses on a single contractor approach to customized renovation work, and performs projects such every bit installing custom tile showers, fixing tiled shower leaks, replacing cracked tiles, and installing floor and wall tile.

  

  Home Renovation & Repair Specialist

  Expert Respond

• Question

  How long does grout need to set for?

  

  Art Fricke
  Domicile Renovation & Repair Specialist

  Fine art Fricke is a dwelling house renovation and repair specialist and the owner of Art Tile & Renovation based in Austin, Texas. With over 10 years of experience, he specializes in bathroom and kitchen renovations. Art focuses on a single contractor arroyo to customized renovation work, and performs projects such as installing custom tile showers, fixing tiled shower leaks, replacing cracked tiles, and installing flooring and wall tile.

  

  Home Renovation & Repair Specialist

  Expert Answer

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

• Wear protective gloves and safety glasses while you remove tiles and so yous don't go injured by any of the tile shards.

• The tiles may be abrupt when you lot suspension or remove them, and then be careful while you're handling them and then you don't accidentally cut yourself.

Advertisement

Things You'll Need

• Drop cloth
• Painter's record
• Grout removal tool
• Hammer
• Flat chisel
• Metal scraper
• Stiff-bristled castor
• Ruler
• Tile mortar
• Square notch trowel
• Replacement tiles
• Tile spacers
• Grout
• Grout bladder
• Sponge

• Grout removal tool
• Hammer
• Flat chisel
• Metal scraper
• Vacuum
• Ruler or measuring tape
• Tile thin-fix
• Square notch trowel
• Tile spacers
• Grout
• Grout float
• Sponge

Nearly This Article

Thanks to all authors for creating a page that has been read 47,266 times.

Did this article help you?

Source: https://www.wikihow.com/Replace-Bathroom-Tiles

Posted by: byrdbefer1969.blogspot.com

Share this post